Close

Mini-Mover Conveyors
a division of Whipple Enterprises

21150 Shake Ridge Road
Volcano,CA 95689 USA

Toll-Free Phone: 800-586-4585
Local Phone: 209-296-5128
Fax: 866-900-5124

[email protected]

1. Select the Conveyor Module

Conveyor
Platform
Width Length
Conveyor Platform divider Conveyor Width Conveyor Height divider
LP Info
Lite Info
A A
Drive
Shaft
Side
T-
Slots
Customer Modifications
* Factory Use Only
Shaft and T-Slot divider Customer Modification
B C

A) Standard width and length of your Lite or LP unit can be chosen from the charts in Section A below. For non-standard sizes, contact your sales representative.

B) Drive shaft location determines which side of the module your drive packaged will be installed on. Dual drive shafts are available on LP series and Lite over- or undermount (O/UM) units. Section B below illustrates the available configurations.

C) Modifications are fairly common since Mini-Movers can handle so many types of applications; see Section C below for more information.

Module Dimension Charts

Lite & LP Standard Widths
Model No.
Width
Reference
Conveyor
Width (W)
02 1.90″
03 2.90″
04 3.90″
06 5.90″
08 7.90″
10 9.90″
12 11.90″
14 13.90″
16 15.90″
Additional widths and extended lengths are available upon request. Ask your sales representative for information.
Lite Series: Standard Lengths
Model No.
Length
Reference
Conveyor
Length (L)
Pulley
Centers (C)
012 12.88″ 10.62″
018 18.68″ 16.15″
024 24.50″ 21.92″
030 30.52″ 27.79″
036 36.52″ 33.98″
042 42.50″ 39.80″
048 48.76″ 46.04″
060 60.75″ 57.85″
072 72.99″ 69.91″
084 85.23″ 82.00″
096 97.47″ 94.06″
108 109.47″ 106.12″
120 121.50″ 118.18″
132 133.50″ 130.24″
144 145.50″ 142.30″
LP Series: Standard Lengths
Conveyor
Length
Reference
Nominal
Conveyor
Length (L)
Reference
Dim. (A)
Pulley
Centers (C)
012 12.00″ 2.20″ 10.62″
018 17.50″ 2.69″ 16.15″
024 23.30″ 2.03″ 21.92″
030 29.33″ 2.69″ 27.79″
036 35.35″ 2.08″ 33.98″
042 41.00″ 2.13″ 39.80″
048 47.43″ 2.16″ 46.04″
060 59.06″ 2.35″ 57.85″
072 71.15″ 2.69″ 69.91″
084 83.30″ 2.68″ 82.00″
096 95.39″ 2.69″ 94.06″
108 107.48″ 2.69″ 106.12″
120 119.57″ 2.70″ 118.18″
132 131.66″ 2.73″ 130.24″
144 143.66″ 2.74″ 142.30″

Conveyor Module Options

Drive Shaft Location determines which side the drive package will mount on.

Drive Shaft Location

Lite O/UM & LP Platforms
Drive Shaft Left Side Drive Shaft Right Side Drive Shaft Both Sides
L – Left Side R – Right Side D – Dual

T-Slot Side Location

LP only LP only LP only
T-Slot LP Left Side T-Slot LP Right Side T-Slot LP Dual Side
L – Left Side R – Right Side D – Dual
LP only Lite only
T-Slot LP No Slot T-Slot Lite No Slot
N – No T-Slot N – No T-Slot

Left- or right-side drive shafts allow mounting of any side-mounted, overmounted or undermounted (O/UM) drive package (see pp. 8-10 for details).

Dual drive shaft location applies to the LP Series or Lite Series O/UM units, for gang-drive applications.

T-Slots, which allow fixtures to be attached, are available only on the LP Series.

Customer Modifications

Lite and LP Series conveyor platforms are readily modified for special applications. The modular nature of Mini-Mover conveyor design can cost-effectively adapt for requirements such as, but not limited to:

  • Ink jet printer and bar coding applications
  • Extended lengths of greater than 144”
  • Non-standard widths and/or lengths
  • Wipedown applications
  • Special drive shaft or gearmotor placement
  • Preparation for severe, dirty and abrasive environments
  • Integration into existing, condensed floorplans or OEM systems
  • Fabrication of special product placement fixtures